









Why buy from us?
Ask a Question About This Product
AMT Electronics E-Drive mini – JFET distortion pedal
Features overview
Drive Series effects are designed to be connected in front of a “clean”
channel inputs of guitar combos or amplifiers, and do not have a cabinet
simulated output as the Legend Amp Series. These pedals allow
guitarists to obtain warm, crisp, natural tube sounds of their favorite
high gain amplifiers, while preserving individuality and tone of the
instrument and equipment.
In the Drive Series, AMT uses new original circuitry solutions developed
by AMT specialists based on real actual tube stage emulation and
response. The result is bright, rich, full, and powerful distortion
sounds.
The AMT E-DRIVE was designed for guitarists looking for distortion sounds similar to that of Engl* amplifiers.
When using Drive Series Effects, the resulting sound is mainly
influenced by the combo or amplifier you use, as well as the speakers
installed in your cabinet. The Drive Series were designed for guitarists
who do not need or desire the speaker emulation of the Legend Amp
Series.
Drive Series pedals provide massive gain, and tonal perfection; just as the tube heads they represent!
CONTROLS:
– The pedal sensitivity and drive/distortion amount is determined by the position of GAIN control.
– The overall output level is determined by the position of LEVEL
control. It’s range of adjustment provides the standard minimum level of
-10dB and reaches +8 dB at it’s maximum position.
– The pedal also features a simplified TONE control, which is designed
for general tone matching of the pedal to your amplifier. Further EQ
adjustment may be made on the expanded preamp section of your amplifier.
– A VOICE switch to cut some mids.
– Standard 9vDC (-) negative center power required. Voltage consumption is low, running at only (less than 4mA) of power.
– TRUE BYPASS circuitry. No tone coloration, signal degregation, or loss while pedals is not in use.AMT Electronics E-Drive mini – JFET distortion pedal
Features overview
Drive Series effects are designed to be connected in front of a “clean”
channel inputs of guitar combos or amplifiers, and do not have a cabinet
simulated output as the Legend Amp Series. These pedals allow
guitarists to obtain warm, crisp, natural tube sounds of their favorite
high gain amplifiers, while preserving individuality and tone of the
instrument and equipment.
In the Drive Series, AMT uses new original circuitry solutions developed
by AMT specialists based on real actual tube stage emulation and
response. The result is bright, rich, full, and powerful distortion
sounds.
The AMT E-DRIVE was designed for guitarists looking for distortion sounds similar to that of Engl* amplifiers.
When using Drive Series Effects, the resulting sound is mainly
influenced by the combo or amplifier you use, as well as the speakers
installed in your cabinet. The Drive Series were designed for guitarists
who do not need or desire the speaker emulation of the Legend Amp
Series.
Drive Series pedals provide massive gain, and tonal perfection; just as the tube heads they represent!
CONTROLS:
– The pedal sensitivity and drive/distortion amount is determined by the position of GAIN control.
– The overall output level is determined by the position of LEVEL
control. It’s range of adjustment provides the standard minimum level of
-10dB and reaches +8 dB at it’s maximum position.
– The pedal also features a simplified TONE control, which is designed
for general tone matching of the pedal to your amplifier. Further EQ
adjustment may be made on the expanded preamp section of your amplifier.
– A VOICE switch to cut some mids.
– Standard 9vDC (-) negative center power required. Voltage consumption is low, running at only (less than 4mA) of power.
– TRUE BYPASS circuitry. No tone coloration, signal degredation, or loss while pedals is not in use.
Technical | |
Pedal Type | Distortion |
True Bypass | Yes |
Batteries | Not supported |
Current Draw | 4 mA |
Inputs | 1/4 TS Guitar input |
Outputs | 1/4 TS Guitar input |
Height | 55 mm |
Depth | 58 mm |
Width | 95 mm |
Weight | 300 gram |
0% Customers recommend this product
-
5 Awesome0%
-
4 Great0%
-
3 Average0%
-
2 Bad0%
-
1 Poor0%
Reviews Over AMT Electronics E-Drive JFET Distortion Pedal
- (0)
Total Reviews (0)
click here write review to add review for this product.
-
(0)
-
(0)
-
(0)
-
(0)
-
(0)
-
(0)